Esta es una plantilla para citar documentos IETF [1] [2] que incluye:
Esta plantilla admite la mayoría de los parámetros disponibles para . Para obtener información sobre dichos parámetros, consulte la documentación de esa plantilla.{{Citation}}
Nota : Todos los nombres de los parámetros deben estar en minúsculas .
|appendix=
– Número de apéndice del documento. |appendix=A.1
produce "sec. A.1" También se utiliza para crear un enlace de anclaje para la URL del documento.|autolink=
– o generar automáticamente un enlace a ietf.org para los documentos especificados con , , , , , o . (habilitado de forma predeterminada)|autolink=yes
|autolink=no
|rfc=
|std=
|bcp=
|fyi=
|draft=
|ien=
|rtr=
|bcp=
– Número del documento de Mejores Prácticas Actuales (BCP). También se utiliza para generar automáticamente un enlace a ietf.org.|draft=
– Nombre del documento borrador de Internet (ID), incluido el borrador principal. También se utiliza para generar automáticamente un enlace a ietf.org.|fyi=
– Número del documento For Your Information (FYI). También se utiliza para generar automáticamente un enlace a ietf.org.|idanchor=
– Destino del enlace de anclaje. De forma predeterminada, no se genera ningún enlace de anclaje. El valor especial |idanchor=ietf
genera un enlace de anclaje adecuado para su uso con el parámetro de esta plantilla . Requiere que |ref=
uno de los campos |id=
, |rfc=
, |std=
, |bcp=
, |fyi=
, |draft=
o esté presente para el texto del enlace de anclaje.|ien=
|rtr=
|idlink=
– Ancla de documento interna o título de un artículo de Wikipedia para vincular mediante el identificador del documento. El artículo ya debe existir. No debe tener un wikilink en sí mismo. No lo use solo, sino junto con |id=
, |rfc=
, |std=
, |bcp=
, |fyi=
, o .|draft=
|ien=
|rtr=
|idlinktype=
– Se puede proporcionar uno de los valores: |id=
, |rfc=
, |std=
, |bcp=
, |fyi=
, |draft=
o para forzar a la plantilla a utilizar el identificador de documento especificado como el texto del vínculo para o . No utilice este valor solo, sino junto con o y , , , , , o .|ien=
|rtr=
|idlinktype=
|idanchor=
|idlink=
|idanchor=
|idlink=
|id=
|rfc=
|std=
|bcp=
|fyi=
|draft=
|ien=
|rtr=
|ien=
– Número del documento Internet Experiment Note (IEN). También se utiliza para generar automáticamente un enlace a ietf.org.|nosec=
– El uso de |section=
, |sections=
, o |appendix=
coloca automáticamente la notación sec. Se |nosec=y
para ocultar la notación sec.|referenceid=
– Identificador de referencia del documento. Se utiliza para crear un enlace de anclaje para la URL del documento.|rfc=
– Número del documento de solicitud de comentarios (RFC). También se utiliza para generar automáticamente un enlace a ietf.org.|rtr=
– Número del documento RARE Technical Reports (RTR). También se utiliza para generar automáticamente un enlace a ietf.org.|section=
– Número de sección del documento. |section=4.3.1
Produce "sec. 4.3.1". También se utiliza para crear un enlace de anclaje para la URL del documento. También se puede utilizar en combinación con |sections=
para vincular a la primera sección del rango de secciones indicado.|sections=
– Rango de secciones del documento. |sections=4.3-4.7
produce "sec. 4.3-4.7"|sectionname=
– El nombre de la sección o título de la sección del documento, escrito completo; se muestra antes |title=
y entre comillas.|std=
– Número del documento del Estándar de Internet (STD). También se utiliza para generar automáticamente un enlace a ietf.org.Al igual que con todas las plantillas de cs1|2, es obligatorio. Si se |title=
omite, la plantilla intentará generar automáticamente un título utilizando el primero de los parámetros |rfc=
, |std=
, |bcp=
, |fyi=
, |draft=
, o identificador de documento, en ese orden.|ien=
|rtr=
|id=
Copia una versión en blanco para utilizarla. Recuerda utilizar el carácter "|" (barra vertical) entre cada parámetro. Elimina los parámetros que no utilices para evitar el desorden en la ventana de edición.
Un dominio es un subdominio de otro dominio si está contenido dentro de ese dominio. Esta relación se puede comprobar observando si el nombre del subdominio termina con el nombre del dominio que lo contiene. Por ejemplo, ABCD es un subdominio de BCD, CD, D y ' '.
Las pruebas de regresión están disponibles aquí:
{{ Cite IETF }} utiliza las siguientes subplantillas:
Los documentos de Solicitud de comentarios (RFC), Para su información (FYI) y Borrador de Internet (ID) se almacenan https://datatracker.ietf.org/doc/html/
y están vinculados de la siguiente manera:
https://datatracker.ietf.org/doc/html/rfc<document number>
https://datatracker.ietf.org/doc/fyi<document number>
https://datatracker.ietf.org/doc/html/draft-<draft name>
Los documentos de Estándar de Internet (STD), Mejores prácticas actuales (BCP), Notas experimentales de Internet (IEN) e Informes técnicos raros (RTR) se almacenan https://rfc-editor.org
y están vinculados de la siguiente manera:
https://www.rfc-editor.org/info/std<document number>
https://www.rfc-editor.org/info/bcp<document number>
https://rfc-editor.org/in-notes/ien/ien<document number>.txt
https://rfc-editor.org/in-notes/museum/RAREreports/rtr<document number>.txt
Los anclajes se generan para la URL utilizando cuatro parámetros:
|section=number
genera#section-<number>
|appendix=number
genera#appendix-<number>
|referenceid=id
genera#ref-<id>
|page=number
genera#page-<number>
La plantilla dará prioridad al primero de los parámetros: |section=
, |appendix=
, |referenceid=
, o |page=
en este orden y creará un ancla utilizando el primer parámetro coincidente.
Esta plantilla produce metadatos COinS ; consulte COinS en Wikipedia para obtener información de fondo.